Plating Rectifiers

Sol Rectifiers PHFSPD

Programmable High Frequency Switching Power Devices

Description

Our plating rectifiers are reasonably priced and suitable for the most demanding electroplating applications:

Anodizing
Brush plating
Electrocoagulation
Electrodegreasing
Electroetching
Electroforming
Electrophoresis
Electroplating
Electropolishing
Electrowinning

Intuitive LCD Interface

plating rectifier interface, electroplating rectifier interface, programmable plating rectifier interface, programmable electroplating rectifier interface

Technology

IGBT programmable high frequency switching power device

DC Smoothed Wave Output

Low ripple smoothed wave plating rectifiers suitable for the most stringent electroplating requirements including single metal, complex multi metal, decorative and hard chrome depositions

Standard Features

CONST – Constant smoothed wave output

PLC communication port RTU RS485

Optional Features

PLC analogue signal communication port 0-10 V or 0-5 V or 4-20 mA
Parallel pairing

Other Available Rectifier Models

Plating Rectifiers

plating rectifier, electroplating rectifier, programmable plating rectifier, programmable electroplating rectifier
plating rectifier controller, electroplating rectifier controller, programmable plating rectifier controller, programmable electroplating rectifier controller
plating rectifier, electroplating rectifier, programmable plating rectifier, programmable electroplating rectifier
plating rectifier controller, electroplating rectifier controller, programmable plating rectifier controller, programmable electroplating rectifier controller
plating rectifier, electroplating rectifier, programmable plating rectifier, programmable electroplating rectifier
plating rectifier controller, electroplating rectifier controller, programmable plating rectifier controller, programmable electroplating rectifier controller
plating rectifier, electroplating rectifier, programmable plating rectifier, programmable electroplating rectifier

Compact Bench Top Plating Rectifiers

Volt Output Range

Standard unit 0~12 V
Other output on request

Ampere Output Range
30 A, 50 A, 100 A, 150 A, 200 A

Remote Control Bench Top Plating Rectifiers

Volt Output Range

Standard unit 0~12 V
Other output on request

Ampere Output Range

50 A, 100 A, 150 A, 200 A, 300 A, 500 A, 1000 A

Remote Control Small Tower Plating Rectifiers

Volt Output Range

Standard unit 0~12 V
Other output on request

Ampere Output Range

1500 A, 2000 A, 2500 A

Remote Control Large Tower Plating Rectifiers

Volt Output Range

Standard unit 0~12 V
Other output on request

Ampere Output Range

3000 A, 4000 A, 5000 A, 6000 A, 7000 A, 8000 A, 10000 A

CONST – Constant Smoothed Wave Output

plating rectifier interface, electroplating rectifier interface, programmable plating rectifier interface, programmable electroplating rectifier interface
Pre-Settable Parameters

Mode CV or CC
Output V or A
Timer for soft start
Timer for soft stop
Timer for auto cut-off
Coulometer for auto cut-off

CV/CC
0 to unit rated output
0 to 9999 S
0 to 9999 S
0 to 9999 S/M/H
*0 to 9999 A/M or A/H

*Coulometer A/M or A/H default value.
12 V 30 – 200 A in A/M, 12 V 300 A and up in A/H.

A Coulometer cumulative total sum is provided.

Simple Operation

Sol Rectifiers PHFSPD

These are programmable closed loop self-regulating units, which output can be set from 0 V to unit rated V output or from 0 A to unit rated A output.

Operator pre-sets unit either in Constant Volt (CV) or in Constant Current (CC) mode.
Then pre-sets required output for the respective selected mode, for instance 6.8 V when in CV mode or 92.7 A when in CC mode.

The moment operator presses the Start key the unit will automatically maintain the pre-set output value no matter any fluctuations in the plating cell resistance or in the main electrical supply to the unit for absolute plating consistency and precise control.

Operator can also pre-set a ramp up time cycle on start. Here the unit will gradually ramp up output to the pre-set output value in the given set time.

Operator can also pre-set a timer or coulometer to control either plating duration or amount of current before the unit automatically cuts off the output and rings the alarm. Very useful to determine metal deposition per batch treatment.

Units are also fitted with a coulometer totalizer to monitor total metal deposition and chemistry consumption. Very useful to determine consumption costs and chemistry replenishment rate.

Durability & Care Free Operation

Relying on our state of the art electronic protection circuitry, our units are known to operate trouble free for years on and into decades.

When units are placed in a clean fresh air environment, care free operation can be expected. Only minimal air fan cleaning may be required once or twice a year.

Order Quantity & Shipping Options

Single order unit are welcomed.

We ship straight from the factory to any parts of the world.

Depending on order weight or volume the following shipping services are available:

Speed courier
Air freight
Air freight door-to-door
Sea freight
Sea freight door-to-door

Worldwide Customers

We have a large number of satisfied customers using on a daily basis our plating rectifiers in various countries, to name a few:

Australia, Austria, China, Denmark, Indonesia, Malaysia, Philippines, New Zealand, Singapore, South Africa, Thailand, United Kingdom of Great Britain, United State of America, Vietnam, etc.

Specifications